REXROTH MSK030C-0900-NN-M1-UP1-NSNN伺服电机
1.产 品 介 绍
品牌:REXROTH
型号说明:REXROTH MSK030C-0900-NN-M1-UP1-NSNN伺服电机
优势:供应进口原装,专业停产配件。
公司主营特点:主营产品各种模块/卡件,控制器,触摸屏,伺服驱动器。
2.产 品 详 情 资 料:
REXROTH MSK030C-0900-NN-M1-UP1-NSNNI/O模块I/O模块用于工厂和模块之间的信号传输和信号匹配。输入和输出电路始终通过前侧的电缆插头馈入I/O模块。数字输出信号的状态显示在电缆插头的LED上。电源通过电缆插头或I/O总线板提供。不同I/O模块类型的顺序无关紧要。I/O模块可以在线插拔。3.8.3(Ex)i-模块当前(Ex)i模块存在于两种结构模型中:REXROTH MSK030C-0900-NN-M1-UP1-NSNN-未涂PCB涂层-涂PCB涂层任何模型都可以一起安装,中间没有自由插槽。未涂漆(Ex)i模块可与未涂漆(Ex)i模块组合在一起,无任何限制。左侧或右侧也不需要空闲插槽。对于带有PCB的涂漆(Ex)i模块,右侧插槽必须与非REXROTH MSK030C-0900-NN-M1-UP1-NSNN(Ex)i模块结合保持自由,或者必须配备带有隔板M 2214的面板。这也适用于插槽15。留给(Ex)i模块的插槽可以配备任何其他模块。备用插槽由面板M 2215(4个)或M 2217(8个)覆盖。
I/O Modules The I/O modules are used for signal transfer and signal matching between the plant and the central modules. The input and output circuits are always fed into the I/O modules via cable plugs on the front side. The status of the digital output signals is shown on the LEDs of the cable plugs. The power supply is either via the cable plugs or via the I/O bus board. The order of the different I/O module types does not matter. The I/O modules can be plugged or unplugged on-line. 3.8.3 (Ex)i-Modules The current (Ex)i modules exist in 2 construction models:REXROTH MSK030C-0900-NN-M1-UP1-NSNN- non-varnished with PCB covering - varnished with PCB covering Any models can be equipped together without free slots between. Non varnished (Ex)i modules may combined together with non-(Ex)i modules without any restrictions. Also no free slots are necessary on the left or on the right. With varnished (Ex)i modules with PCB covering the right slot has to remain free in combination with non-(Ex)i modulels or has to be equipped with with a faceplate with partition plate M 2214. This is also valid for slot 15. The slot left to the (Ex)i module may be equipped with any other module. Spare slots are to be covered by faceplates M 2215 (4 units) or M 2217 (8 units).REXROTH MSK030C-0900-NN-M1-UP1-NSNN
3.产 品 展 示
4.公 司 优 势 主 营 产 品
5.关 于 相 关 产 品 展 示
本篇文章出自瑞昌明盛自动化设备有限公司,转载请附上此链接:
所有评论仅代表网友意见,与本站立场无关。