规格
Water Specifications
Milli-Q® Integral ultrapure water (Type 1)
| Resistivity at 25 °C1 | 18.2 MΩ•cm |
| TOC2 | ≤ 5 ppb |
| Particulates (size > 0.22 μm)3 | < 1 particulate/mL |
| Bacteria3,4 | < 0.01 CFU/mL |
| Pyrogens (endotoxins)4 | < 0.001 EU/mL |
| RNases4 | < 1 pg/mL |
| DNases4 | < 5 pg/mL |
| Flow Rate | Up to 2 L/min |
| 1resistivity can also be displayed non-temperature-compensated as required by USP 2in the appropriate test conditions 3with Millipak® final filter 4with Biopak® polisher These values are typical and may vary depending on the nature and concentration of contaminants in the feed water. | |
Milli-Q® Integral pure water (Type 2)
| Resistivity at 25 °C1 | Typically 10-15 MΩ•cm |
| TOC | < 30 ppb |
| Production flow Rate | 3 L/h (Milli-Q® Integral 3) 5 L/h (Milli-Q® Integral 5) 10 L/h (Milli-Q® Integral 10) 15 L/h (Milli-Q® Integral 15) |
| From an E-POD® dispenser with final filter, the following water quality specifications are achieved: | |
| Particulates (size > 0.22 µm)2 | < 1 particulate/mL |
| Bacteria2,3 | < 0.1 CFU/mL |
| Pyrogens (endotoxins)3 | < 0.001 EU/mL |
| RNases3 | < 0.01 ng/mL |
| DNases3 | < 4 pg/µL |
| Flow Rate | Up to 2 L/min |
| 1Resistivity can also be displayed non-temperature-compensated as required by USP 2with Millipak® final filter 3with Biopak® Polisher | |
Feed water
| Feed water quality | Potable tap water as described in US-EPA, EP and WHO norms |
| Feed water connection | ½" Gaz M |
| Feed water pressure* | 1 - 6 bar |
| Feed water temperature | 5 - 35 °C |
| * For pressure above 6 bar, a pressure regulator needs to be installed upstream of the system | |
System Specifications
Production unit
| Dimensions (H x W x D) | 500 x 332 x 484 mm (19.7 x 13.0 x 19.0 in) |
| Operating weight | 24 - 28 kg (52.9 - 61.7 lb) |
| Electric power supply voltage | 100 - 230 V +/- 10% |
| Electric power supply frequency | 50 - 60 Hz +/- 10% |
| Milli-Q® Integral main unit data connection | Ethernet (RJ45) |
Q-POD® & E-POD® dispensers
| Dimensions (H x D) | 579 x 230 mm (22.8 x 9.0 in) |
| Operating weight | 4.7 kg (12.1 lb) |
| Dispenser tubing length | 0.8 m (31.5 in) |
| Distance from production unit to Q-POD® | 2.9 m (9.5 ft) |
| Electric power cable length | 2.9 m (9.5 ft) |
| Q-POD® data connection | Parallel port (25-pin D-Sub) |
所有评论仅代表网友意见，与本站立场无关。