AN锁紧螺帽AN螺帽结构简单，内螺纹和端面同时加工，可确保偏摆精度要求。
AN螺帽结构简单，内螺纹和端面同时加工，可确保偏摆精度要求。
• 硬度：HRC26 °~28°
• 螺纹精度：ISO 4H
• 加工方式：精密车削
• 平面偏摆：0.005mm
| Thread | D | h | g | t | d |
| AN 0-M10x0.75P | 18 | 4 | 3 | 2 | 13.5 |
| AN 1-M12x1.0P | 22 | 17 | |||
| AN 2-M15x1.0P | 25 | 5 | 4 | 21 | |
| AN 3-M17x1.0P | 28 | 24 | |||
| AN 4-M20x1.0P | 32 | 6 | 26 | ||
| AN 5-M25x1.5P | 38 | 7 | 5 | 32 | |
| AN 6-M30x1.5P | 45 | 38 | |||
| AN 7-M35x1.5P | 52 | 8 | 44 | ||
| AN 8-M40x1.5P | 58 | 9 | 6 | 2.5 | 50 |
| AN 9-M45x1.5P | 65 | 10 | 56 | ||
| AN 10-M50x1.5P | 70 | 11 | 61 | ||
| AN 11-M55x2.0P | 75 | 7 | 3 | 67 | |
| AN 12-M60x2.0P | 80 | 73 | |||
| AN 13-M65x2.0P | 85 | 12 | 79 | ||
| AN 14-M70x2.0P | 92 | 8 | 3.5 | 85 | |
| AN 15-M75x2.0P | 98 | 13 | 90 | ||
| AN 16-M80x2.0P | 105 | 15 | 95 | ||
| AN 17-M85x2.0P | 110 | 16 | 102 | ||
| AN 18-M90x2.0P | 120 | 10 | 4 | 108 | |
| AN 19-M95x2.0P | 125 | 17 | 113 | ||
| AN 20-M100x2.0P | 130 | 18 | 120 | ||
| AN 21-M105x2.0P | 140 | 12 | 5 | 126 | |
| AN 22-M110x2.0P | 145 | 19 | 133 | ||
| AN 23-M115x2.0P | 150 | 137 | |||
| AN 24-M120x2.0P | 155 | 20 | 138 | ||
| AN 25-M125x2.0P | 160 | 21 | 148 | ||
| AN 26-M130x2.0P | 165 | 149 | |||
| AN 27-M135x2.0P | 175 | 22 | 14 | 6 | 160 |
| AN 28-M140x2.0P | 180 | ||||
| AN 29-M145x2.0P | 190 | 24 | 172 | ||
| AN 30-M150x2.0P | 195 | 171 | |||
| AN 31-M155x2.0P | 200 | 25 | 16 | 7 | 182 |
| AN 32-M160x3.0P | 210 | ||||
| AN 33-M165x3.0P | 26 | 193 | |||
| AN 34-M170x3.0P | 220 | ||||
| AN 36-M180x3.0P | 230 | 27 | 18 | 8 | 203 |
| AN 38-M190x3.0P | 240 | 28 | 214 | ||
| AN 40-M200x3.0P | 250 | 29 | 226 |
所有评论仅代表网友意见，与本站立场无关。