西门子6ES75211FH000AA0性能参数 西门子6ES75211FH000AA0性能参数

6ES7521-1FH00-0AA0

SIMATIC S7-1500, 数字量输入模块 DI 16xAC 230V, 16 通道 8 个一组; 输入延迟 20ms; 输入类型 1(IEC 61131)

公司名称：上海朔川电气设备有限公司
联系人：吉梦琪
：
地址：上海市金山区泾波路129号
：2840735331

SM 521 数字量输入模块

订货数据
附件
产品信息
组态工具

跳转到

概述

应用

设计

功能

技术规范

概述

16 和 32 通道数字量输入模块
灵活地选择控制器以满足相应任务需要
用于使用附加输入对系统进行后续扩展
35 mm 宽的模块具有参数设置和诊断功能
25 mm 宽的模块可在狭小空间内使用：
极为经济，无参数设置或诊断功能

应用

数字量输入模块可记录设备中的 24 V DC 或 230 V AC 信号，并将它们传送到控制器。可以连接开关以及 2 线制、3 线制或 4 线制接近开关。

35 mm 宽的输入模块具有可设定的参数和诊断功能，因此可根据相应过程要求进行灵活调整。

25 mm 宽的低成本模块没有可设定的参数或诊断功能，可极为方便地集成到工程系统中。建议将它们在只需要很少输入通道的位置使用，或在必须在十分有限的空间内部署大量通道的情况下使用。

根据需要，可在一个站中并排使用两种模块。由于具有统一特性并采用共同的系统附件，处理十分方便。

提供了以下宽度为 35 mm 的数字量输入模块：

DI 16x24VDC HF；
16 通道数字量输入模块，用于记录 24 V DC 信号；一个电压组；输入延迟 0.05 ... 20 ms；输入类型 3 (IEC 61131)；可设置诊断和硬件中断
DI 32x24VDC HF;
32 通道数字量输入模块，用于记录 24 V DC 信号；两个电压组；输入延迟 0.05 ... 20 ms；输入类型 3 (IEC 61131)；可设置诊断和硬件中断
DI 16x24VDC SRC BA;
16 通道数字量输入模块，用于记录 24 V DC 信号；低电平有效；一个电压组；固定输入延迟 3.2 ms；输入类型 3 (IEC 61131)
DI 16x230VAC BA;
16 通道数字量输入模块，用于记录 230 V DC 信号；低电平有效；一个电压组；固定输入延迟 20 ms；输入类型 1 (IEC 61131)

提供了以下宽度为 25 mm 的数字量输入模块：

DI 16x24VDC BA;
16 通道数字量输入模块，用于记录 24 V DC 信号；漏型输入；一个电压组；固定输入延迟 3.2 ms；输入类型 3 (IEC 61131)
DI 32x24VDC BA;
32 通道数字量输入模块，用于记录 24 V DC 信号；漏型输入；一个电压组；固定输入延迟 3.2 ms；输入类型 3 (IEC 61131)

设计

用一个螺丝安装在 S7-1500 安装导轨上
35 mm 模块采用螺钉型端子或推入式端子的标准化 40 针前连接器（不能用于 25 mm 模块）
25 mm 模块采用推入式端子的标准化 40 针前连接器（不能用于 35 mm 模块）
标准化、协调型前连接器针脚分配，更便于接线
可连接芯线截面积0.25 mm² 至 1.5 mm²（AWG24 至 16）
集成式电压桥接件，用于灵活形成电压组(仅 35 mm 模块)
前连接器的预接线位置
前盖带有可扩充的电缆室，即使*接线时也如此
模块正面的清晰标签
- 模块类型
- 订货号
- 硬件和固件型号
- 通道编号标签
- 电缆连接图

含在供货范围之内：

用于手工贴标签的一个标签条
一个 U 型连接器
印制有文字的前门
前连接器（(仅 25 mm 模块）

功能

统一的显示和诊断方式：
- 故障（红色 LED）和运行（绿色 LED）模块状态显示
- 用于信号状态日志的信号状态显示。"0" 和日志。 "1"（绿色 LED），或者，指示线断（红色 LED）
- 显示 24 V DC 电源电压（绿色 LED）
支持的功能：
- 识别和维护数据 IM0 至 IM3
- 固件更新
- 模块级别的共享设备和 MSI（模块化共享输入）；
  与 PROFINET 结合使用时，可将这些模块分配给多个 IO 控制器
- 与通道有关的参数分配（* HF 模块）
- 硬件中断（* HF 模块）
- 按通道进行诊断（* HF 模块）
- 等时同步模式（取决于模块）

技术规范

Article number	6ES7521-1BH00-0AB0	6ES7521-1BL00-0AB0	6ES7521-1BH50-0AA0	6ES7521-1FH00-0AA0	6ES7521-7EH00-0AB0
	S7-1500, DI 16X24VDC HF	S7-1500, DI 32X24VDC HF	S7-1500, DI 16X24VDC SRC BA	S7-1500, DI 16X230VAC BA	S7-1500, DI 16 X 24...125V UC HF
General information
Product type designation	DI 16x24VDC HF	DI 32x24VDC HF	DI 16x24VDC SRC BA	DI 16x230VAC BA
HW functional status	FS01	FS01	FS01	FS01	FS01
Firmware version	V2.1.0	V2.1.0	V2.0.0	V2.0.0	V1.0.0
● FW update possible	Yes	Yes	Yes	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 SP1 / -	V13 SP1 / -	V12 / V12	V12 / V12	V13 SP1 / -
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -
Operating mode
● DI	Yes	Yes	Yes	Yes	Yes
● Counter	Yes	Yes	No	No	No
● Oversampling	No	No			No
● MSI	Yes	Yes	Yes	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes	Yes
Input current
Current consumption, max.	20 mA; with 24 V DC supply	40 mA; 20 mA per group with 24 V DC supply
Power
Power available from the backplane bus	1.1 W	1.1 W	0.9 W	1 W	1.2 W
Power loss
Power loss, typ.	2.6 W	4.2 W	2.8 W	4.9 W	2.2 W; At 24 V DC; 6.0 W at 125 V AC
Digital inputs
Number of digital inputs	16	32	16	16	16
Digital inputs, parameterizable	Yes	Yes	No	No	Yes
Source/sink input	P-reading	P-reading	m-reading	P-reading	Yes
Input characteristic curve in accordance with IEC 61131, type 1				Yes
Input characteristic curve in accordance with IEC 61131, type 3	Yes	Yes	Yes		Yes; at 24 V DC
Digital input functions, parameterizable
● Gate start/stop	Yes	Yes
● Freely usable digital input	Yes	Yes
● Counter
— Number, max.	2	2
— Counting frequency, max.	1 kHz	1 kHz
— Counting width	32 bit	32 bit
— Counting direction up/down	Up	Up
Input voltage
● Type of input voltage	DC	DC	DC	AC	AC/DC
● Rated value (DC)	24 V	24 V	24 V		24 V; 48 V, 125 V
● Rated value (AC)				230 V; 120/230V AC, 50/60 Hz	24 V; 48 V, 125 V (50 - 60 Hz)
● for signal "0"	-30 to +5V	-30 to +5V	-5 to +30V	0V AC to 40V AC	-5 ... +5 V
● for signal "1"	+11 to +30V	+11 to +30V	-11 to -30V	79V AC to 264V AC	+11 ... +146 V
Input current
● for signal "1", typ.	2.5 mA	2.5 mA	4.5 mA	11 mA; At 230 V AC and 5.5 mA at 120 V AC	3 mA; at 24 V DC
Input delay (for rated value of input voltage)
for standard inputs
— parameterizable	Yes; 0.05 / 0.1 / 0.4 / 1.6 / 3.2 / 12.8 / 20 ms	Yes; 0.05 / 0.1 / 0.4 / 1.6 / 3.2 / 12.8 / 20 ms	No	No	Yes; 0.05 / 0.1 / 0.4 / 1.6 / 3.2 / 12.8 / 20 ms parameterizable with DC, 20 ms fixed with AC
— at "0" to "1", min.	0.05 ms	0.05 ms	3 ms		0.05 ms
— at "0" to "1", max.	20 ms	20 ms	4 ms	25 ms	20 ms
— at "1" to "0", min.	0.05 ms	0.05 ms	3 ms		0.05 ms
— at "1" to "0", max.	20 ms	20 ms	4 ms	25 ms	20 ms
for interrupt inputs
— parameterizable	Yes	Yes	No	No	Yes
for counter/technological functions
— parameterizable	Yes	Yes	No	No	No
Cable length
● shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m	1 000 m
● unshielded, max.	600 m	600 m	600 m	600 m	600 m
Encoder
Connectable encoders
● 2-wire sensor	Yes	Yes	Yes	Yes	Yes
— permissible quiescent current (2-wire sensor), max.	1.5 mA	1.5 mA	1.5 mA	2 mA	1.5 mA
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	Yes	No	No	No
Filtering and processing time (TCI), min.	80 µs; At 50 μs filter time	80 µs; At 50 μs filter time
Bus cycle time (TDP), min.	250 µs	250 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	No	No	Yes
Alarms
● Diagnostic alarm	Yes	Yes	No	No	Yes
● Hardware interrupt	Yes	Yes	No	No	Yes
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes	No	No	No
● Wire-break	Yes; to I < 350 µA	Yes; to I < 350 µA	No	No	Yes; To I < 550 µA
● Short-circuit	No	No	No	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED	No	No	No
● Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● for channel diagnostics	Yes; Red LED	Yes; Red LED	No	No	Yes; Red LED
● for module diagnostics	Yes; Red LED	Yes; Red LED	No	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels	No	Yes	No	No	Yes
● between the channels, in groups of	16	16	16	4	1
● between the channels and backplane bus	Yes	Yes	Yes	Yes	Yes
● between the channels and the power supply of the electronics	No	No
Permissible potential difference
between different circuits				250 V AC between the channels and the backplane bus; 500 V AC between the channels	146 V DC/132 V AC
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)	707 V DC (type test)	3 100 V DC	2 000 V DC
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C	0 °C	0 °C	0 °C	0 °C
● horizontal installation, max.	60 °C	60 °C	60 °C	60 °C	60 °C
● vertical installation, min.	0 °C	0 °C	0 °C	0 °C	0 °C
● vertical installation, max.	40 °C	40 °C	40 °C	40 °C	40 °C
Decentralized operation
Prioritized startup	Yes	Yes	Yes	Yes	Yes
Dimensions
Width	35 mm	35 mm	35 mm	35 mm	35 mm
Height	147 mm	147 mm	147 mm	147 mm	147 mm
Depth	129 mm	129 mm	129 mm	129 mm	129 mm
Weights
Weight, approx.	240 g	260 g	230 g	300 g	240 g

Article number	6ES7521-1BH10-0AA0	6ES7521-1BL10-0AA0
	S7-1500, DI 16X24VDC BA	S7-1500, DI 32X24VDC BA
General information
Product type designation	DI 16 x 24 V DC BA	DI 32x24VDC BA
HW functional status	FS01	FS01
Firmware version	V1.0.0	V1.0.0
● FW update possible	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 / V13	V13 / V13
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -
Operating mode
● DI	Yes	Yes
● Counter	No	No
● MSI	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Power
Power available from the backplane bus	1.05 W	1.05 W
Power loss
Power loss, typ.	1.8 W	3 W
Digital inputs
Number of digital inputs	16	32
Digital inputs, parameterizable	No	No
Source/sink input	P-reading	P-reading
Input characteristic curve in accordance with IEC 61131, type 3	Yes	Yes
Input voltage
● Type of input voltage	DC	DC
● Rated value (DC)	24 V	24 V
● for signal "0"	-30 to +5V	-30 to +5V
● for signal "1"	+11 to +30V	+11 to +30V
Input current
● for signal "1", typ.	2.7 mA	2.7 mA
Input delay (for rated value of input voltage)
for standard inputs
— parameterizable	No	No
— at "0" to "1", min.	3 ms	3 ms
— at "0" to "1", max.	4 ms	4 ms
— at "1" to "0", min.	3 ms	3 ms
— at "1" to "0", max.	4 ms	4 ms
for interrupt inputs
— parameterizable	No	No
for counter/technological functions
— parameterizable	No	No
Cable length
● shielded, max.	1 000 m	1 000 m
● unshielded, max.	600 m	600 m
Encoder
Connectable encoders
● 2-wire sensor	Yes	Yes
— permissible quiescent current (2-wire sensor), max.	1.5 mA	1.5 mA
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No
Interrupts/diagnostics/status information
Diagnostics function	No	No
Alarms
● Diagnostic alarm	No	No
● Hardware interrupt	No	No
Diagnostic messages
● Monitoring the supply voltage	No	No
● Wire-break	No	No
● Short-circuit	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	No	No
● Channel status display	Yes; Green LED	Yes; Green LED
● for channel diagnostics	No	No
● for module diagnostics	No	No
Potential separation
Potential separation channels
● between the channels	No	No
● between the channels, in groups of	16	16
● between the channels and backplane bus	Yes	Yes
● between the channels and the power supply of the electronics		No
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C	0 °C
● horizontal installation, max.	60 °C	60 °C
● vertical installation, min.	0 °C	0 °C
● vertical installation, max.	40 °C	40 °C
Decentralized operation
Prioritized startup	Yes	Yes
Dimensions
Width	25 mm	25 mm
Height	147 mm	147 mm
Depth	129 mm	129 mm
Weights
Weight, approx.	230 g	260 g
Other
Note:	Supplied incl. 40-pole push-in front connectors	Supplied incl. 40-pole push-in front connectors

全部关于 SM 521 数字量输入模块

产品与解决方案在线目录与订购系统技术信息服务与支持与合作伙伴服务项目

西门子6ES75211FH000AA0性能参数

SM 521 数字量输入模块

跳转到

概述

应用

设计

功能

技术规范

在线询价

收藏该商铺

提示

提示

西门子6ES75211FH000AA0性能参数

SM 521 数字量输入模块

跳转到

概述

应用

设计

功能

技术规范

在线询价

会员登录

收藏该商铺

提示

提示